Mandatory BIS Certification for Aluminium Alloy Miscellaneous Products: A Guide for Foreign Manufacturers

Introduction

The Indian government has made BIS certification for aluminium alloy products mandatory through a new Quality Control Order (QCO) under the BIS Act, 2016. It is done to ensure high standards in manufacturing and public safety. This regulation continues to apply to foreign manufacturers who wish to export aluminium products to India. The BIS FMCS certification for aluminium alloy miscellaneous products is now a legal requirement before entering the Indian market. If you are an international manufacturing company planning to export aluminium alloy products in India, then this guide is meant to help you understand how to process it, the documents you will require, and how to easily do it. 

Understanding the BIS Certification for Foreign Manufacturers

The Bureau of Indian Standards (BIS) is the national standards organisation in India, and regulates the quality of products and product safety. In the case of foreign firms, Scheme I of the BIS Conformity Assessment Regulations, 2018, runs the Foreign Manufacturers Certification Scheme (FMCS), which allows foreign firms to use Marking Scheme I. Any foreign manufacturer seeking BIS approval must go through FMCS to legally apply the ISI Mark on products intended for the Indian market. It is a compulsory certification, and failure to certify products may lead to restrictions on imports or even fines.

Overview of the Aluminium Alloy Products QCO, 2025

The Aluminium Alloy Miscellaneous Products (Quality Control) Order, 2025 was published at the Ministry of Commerce and Industry. It makes it mandatory that certain products of aluminium have to be manufactured up to Indian Standards and acquire the ISI Mark.

Products covered under this QCO:

• Aluminium Alloy Milk Cans – IS 1825:1983
• Aluminium Alloy Redraw Rods – IS 9997:2023
• Aluminium Alloy Hardeners (Master Alloys) – IS 2047:1992

Effective Dates:

• General manufacturers: 6 months from notification
• Small enterprises: 9 months from notification
• Micro enterprises: 12 months from notification

Also Read: Significance of FMCS Certification in India

BIS FMCS Certification for Aluminium Alloy Products: Step-by-Step Guide

The process of obtaining BIS FMCS certification for aluminium alloy products has many stages. The stages are mentioned below:

1. Application Submission

   • Register on the BIS portal.
   • Fill and submit Form VI for foreign manufacturers.
   • Pay applicable fees.

2. Product Testing

   • The product should be submitted to a BIS-recognised laboratory.
   • Testing should be done by the concerned Indian Standard (like IS 1825:1983, IS 9997:2023, or IS 2047:1992).

3. Documentation Review

   • Upload all required documents.
   • BIS examines the compliance documentation.

4. Factory Inspection

   • BIS officials conduct a physical audit at the manufacturing facility.
   • They are used to assure the manufacturing capacity, the level of quality control and the test equipment.

5. Grant of License

   • BIS provides the license for inspection and verification

Required Documents to Get a BIS Foreign Manufacturer Certificate

Below is the list of documents required to get a BIS Foreign Manufacturer Certificate:

• Business license and company registration certificate.
• List of raw materials and suppliers.
• Internal quality control procedures.
• Product test reports from BIS-recognised labs.
• Machinery and testing equipment list.
• Authorisation letter for the Indian representative (if applicable).
• Undertaking for compliance with BIS rules.
• Sample product labels and packaging.

Key Challenges Faced by Foreign Manufacturers

1. Logistical Hurdles

   Shipping the samples outside the country to have them tested could be costly.

2. Low level of Local Knowledge

   The language, standards and documentation related to the regulation of business may be unfamiliar to foreign firms.

3. Factory Inspections Trial

   The supervision visits must be planned far ahead, and time differences and required travelling may delay them.

4. Few Recognised Labs Overseas

   Not many labs approved by BIS are outside India, and even localised testing is not easy.

5. Communication Delays

   The response to BIS correspondence may take some time because of the administrative workloads and follow-up formalities.

Brand Liaison India (A certified BIS consultant) can help in making this process hassle-free. 

Our scope of work

As a reliable compliance provider, Brand Liaison provides complete foreign manufacturer BIS support comprising:

• Preliminary consultation: Learning about your product and what you need to know to meet the requirements.
• Documentation and verification: Making sure that all the necessary paperwork is correct and BIS compliant.
• Logistic coordination of product sample testing: Arrangement of logistics with established laboratories.
• Pre-audit-check: Making your product fit to be checked by BIS.
• End-to-end interaction with the BIS: We coordinate this and make the follow-ups on the process of getting the license with the BIS.

Brand Liaison has the expertise to save your time, prevent rejections, and get your aluminium alloy products approved to the Indian market in the most hassle-free and efficient manner.

Also Read: Mandatory BIS Certification Guide for Aluminium Composite Panel

Conclusion

BIS certification on the aluminium alloy products is mandatory. The Aluminium Alloy Products QCO, 2025, requires that the manufacturers around the world attain the BIS FMCS certification in order to export their products to India as required by law. Whether you're dealing with aluminium milk cans, redraw rods, or master alloys, a certification consultant like Brand Liaison can make the difference between delay and success.